Fluorescein-5-isothiocyanate (FITC)

製品コードS6928 バッチS692801

化学情報

	Synonyms	Fluorescein isothiocyanate isomer I, 5-FITC	Storage (From the date of receipt)	3 years -20°C(in the dark) powder
	化学式	C₂₁H₁₁NO₅S
	分子量	389.38	CAS No.	3326-32-7
Solubility (25°C)*	体外	DMSO	78 mg/mL (200.31 mM)
		Ethanol	10 mg/mL (25.68 mM)
		Water	Insoluble
* <1 mg/ml means slightly soluble or insoluble. * Please note that Selleck tests the solubility of all compounds in-house, and the actual solubility may differ slightly from published values. This is normal and is due to slight batch-to-batch variations.

溶剤液（一定の濃度）を調合する

生物活性

製品説明	Fluorescein-5-isothiocyanate (FITC, Fluorescein isothiocyanate isomer I, 5-FITC) is a fluorescent probe capable of being conjugated to tissue and proteins.
in vitro	1.Protein Preparetion 1) In order to obtain the best labeling effect, please prepare the protein (antibody) concentration as 2 mg/mL. 2) The pH value of protein solution shall be 8.5±0.5. If the pH is lower than 8.0, 1m sodium bicarbonate shall be used for adjustment. 3) If the protein concentration is lower than 2mg/ml, the labeling efficiency will be greatly reduced. In order to obtain the best labeling efficiency, it is recommended that the final protein concentration range is 2-10 mg/mL. 4) The protein must be in the buffer without primary amine (such as Tris or glycine) and ammonium ion, otherwise the labeling efficiency will be affected. 2.Dye Preparation Add anhydrous DMSO into the vial of FITC to make a 10 mM stock solution. Mix well by pipetting or vortex. 3.Calculation of dye dosage The amount of FITC required for reaction depends on the amount of protein to be labeled, and the optimal molar ratio of FITC to protein is about 10. Example: assuming the required marker protein is 1 mL 2 mg/mL IgG (MW=150,000), use 1 mL DMSO dissolve 1 mg FITC, the required FITC volume is 40 μL. 4.Run conjugation reaction 1) A good volume of freshly prepared 10 mg/mL FITC is slowly added to 0.5 mL protein sample. In solution, gently shake to mix, then centrifuge briefly to collect the sample at the bottom of the reaction tube. Don't mix well to prevent protein samples from denaturation and inactivation. 2) The reaction tubules were placed in a dark place and incubated gently at room temperature for 60 minutes at intervals.For 10-15 minutes, gently reverse the reaction tubules several times to fully mix the two reactants and raise the bar efficiency. 5.Purify the conjugation The following protocol is an example of dye-protein conjugate purification by using a Sephadex G-25 column. 1) Prepare Sephadex G-25 column according to the manufacture instruction. 2) Load the reaction mixture (From ""Run conjugation reaction"") to the top of the Sephadex G-25 column. 3) Add PBS (pH 7.2-7.4) as soon as the sample runs just below the top resin surface. 4) Add more PBS (pH 7.2-7.4) to the desired sample to complete the column purification. Combine the fractions that contain the desired dye-protein conjugate.

製品説明

Fluorescein-5-isothiocyanate (FITC, Fluorescein isothiocyanate isomer I, 5-FITC) is a fluorescent probe capable of being conjugated to tissue and proteins.

in vitro

1.Protein Preparetion
1) In order to obtain the best labeling effect, please prepare the protein (antibody) concentration as 2 mg/mL.
2) The pH value of protein solution shall be 8.5±0.5. If the pH is lower than 8.0, 1m sodium bicarbonate shall be used for adjustment.
3) If the protein concentration is lower than 2mg/ml, the labeling efficiency will be greatly reduced. In order to obtain the best labeling efficiency, it is recommended that the final protein concentration range is 2-10 mg/mL.
4) The protein must be in the buffer without primary amine (such as Tris or glycine) and ammonium ion, otherwise the labeling efficiency will be affected.
2.Dye Preparation
Add anhydrous DMSO into the vial of FITC to make a 10 mM stock solution. Mix well by pipetting or vortex.
3.Calculation of dye dosage
The amount of FITC required for reaction depends on the amount of protein to be labeled, and the optimal molar ratio of FITC to protein is about 10.
Example: assuming the required marker protein is 1 mL 2 mg/mL IgG (MW=150,000), use 1 mL DMSO dissolve 1 mg FITC, the required FITC volume is 40 μL.
4.Run conjugation reaction
1) A good volume of freshly prepared 10 mg/mL FITC is slowly added to 0.5 mL protein sample. In solution, gently shake to mix, then centrifuge briefly to collect the sample at the bottom of the reaction tube. Don't mix well to prevent protein samples from denaturation and inactivation.
2) The reaction tubules were placed in a dark place and incubated gently at room temperature for 60 minutes at intervals.For 10-15 minutes, gently reverse the reaction tubules several times to fully mix the two reactants and raise the bar efficiency.
5.Purify the conjugation
The following protocol is an example of dye-protein conjugate purification by using a Sephadex G-25 column.
1) Prepare Sephadex G-25 column according to the manufacture instruction.
2) Load the reaction mixture (From ""Run conjugation reaction"") to the top of the Sephadex G-25 column.
3) Add PBS (pH 7.2-7.4) as soon as the sample runs just below the top resin surface.
4) Add more PBS (pH 7.2-7.4) to the desired sample to complete the column purification.
Combine the fractions that contain the desired dye-protein conjugate.

プロトコル(参考用のみ)

Selleckの高級品が、幾つかの出版された研究調査結果（以下を含む）で使われた：

Circular RNA circ-MMP11 Contributes to Lapatinib Resistance of Breast Cancer Cells by Regulating the miR-153-3p/ANLN Axis [ Front Oncol, 2021, 11:639961]	PubMed: 34295807

Circular RNA circ-MMP11 Contributes to Lapatinib Resistance of Breast Cancer Cells by Regulating the miR-153-3p/ANLN Axis [ Front Oncol, 2021, 11:639961]

PubMed: 34295807

長期の保管のために-20°Cの下で製品を保ってください。

人間や獣医の診断であるか治療的な使用のためにでない。

各々の製品のための特定の保管と取扱い情報は、製品データシートの上で示されます。大部分のSelleck製品は、推薦された状況の下で安定です。製品は、推薦された保管温度と異なる温度で、時々出荷されます。長期の保管のために必要とされてそれと異なる温度で、多くの製品は、短期もので安定です。品質を維持するが、夜通しの積荷のために最も経済的な貯蔵状況を用いてあなたの送料を保存する状況の下に、製品が出荷されることを、我々は確実とします。製品の受領と同時に、製品データシートの上で貯蔵推薦に従ってください。