DFCP1 Antibody (Rabbit mAb) [G16K2]

製品コード:F7517

印刷

生物学的記述

Specificity DFCP1 Antibody (Rabbit mAb) [G16K2] detects endogenous levels of total DFCP1 protein.
Background DFCP1 (double FYVE-containing protein 1, ZFYVE1) is a phosphatidylinositol 3-phosphate (PI3P)-binding protein of the FYVE-domain family. It is the defining marker of omegasomes, the cup-shaped regions of the endoplasmic reticulum (ER) where autophagosomes form. Its domain layout pairs an N-terminal region with ATPase activity, a central region that targets it to the ER, and tandem C-terminal FYVE zinc-finger domains that recognize PI3P on membranes. DFCP1 normally sits on ER and Golgi membranes. Amino acid starvation moves it, in a PI3P-dependent way, into punctate omegasomes that grow from ER membranes. These sit next to vesicles carrying Vps34, the kinase that makes PI3P, and they associate with the autophagy proteins Atg5 and LC3/Atg8. Nascent autophagosomes grow out of these PI3P-rich platforms, which stay dynamically connected to the ER. A DFCP1 mutant that cannot bind PI3P stays in the ER and fails to reach omegasomes. DFCP1 overexpression inhibits autophagy, probably by sequestering PI3P from other PI3P effectors, and DFCP1 itself is not required for autophagosome formation at the omegasome. Its specific role depends on its ATPase activity. DFCP1 hydrolyzes ATP, membrane binding stimulates this activity, and the protein dimerizes in an ATP-dependent way. Mutants that cannot bind or hydrolyze ATP still reach forming omegasomes but cannot constrict them properly, especially the large ones, so nascent autophagosomes are released much more slowly. Depleting DFCP1 barely affects bulk autophagic flux but impairs the turnover of the cargo adaptor p62/SQSTM1 under both fed and starved conditions. DFCP1 knockout inhibits several selective autophagy pathways, including the clearance of protein aggregates (aggrephagy), damaged mitochondria (mitophagy) and micronuclei.

使用情報

Application WB Dilution
WB
1:1000
Reactivity Human, Mouse, Rat
Source Rabbit Monoclonal Antibody MW 87 kDa
Storage Buffer PBS, pH 7.2+50% Glycerol+0.05% BSA+0.01% NaN3
Storage
(from the date of receipt)
-20°C (avoid freeze-thaw cycles), 2 years
WB
Experimental Protocol:
 
Sample preparation
1. Tissue: Lyse the tissue sample by adding an appropriate volume of ice-cold RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail),and homogenize the tissue at a low temperature or lyse it by sonication on ice, then incubate on ice for 30 minutes.
2. Adherent cell: Aspirate the culture medium and wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
3. Suspension cell: Transfer the culture medium to a pre-cooled centrifuge tube. Centrifuge and aspirate the supernatant. Wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
4. Place the lysate into a pre-cooled microcentrifuge tube. Centrifuge at 4°C for 15 min. Collect the supernatant;
5. Remove a small volume of lysate to determine the protein concentration;
6. Combine the lysate with protein loading buffer. Boil 20 µL sample under 95-100°C for 5 min. Centrifuge for 5 min after cool down on ice.
 
Electrophoretic separation
1. According to the concentration of extracted protein, load appropriate amount of protein sample and marker onto SDS-PAGE gels for electrophoresis. Recommended separating gel (lower gel) concentration: 10%. Reference Table for Selecting SDS-PAGE Separation Gel Concentrations
2. Power up 80V for 30 minutes. Then the power supply is adjusted (110 V~150 V), the Marker is observed, and the electrophoresis can be stopped when the indicator band of the predyed protein Marker where the protein is located is properly separated. (Note that the current should not be too large when electrophoresis, too large current (more than 150 mA) will cause the temperature to rise, affecting the result of running glue. If high currents cannot be avoided, an ice bath can be used to cool the bath.)
 
Transfer membrane
1. Take out the converter, soak the clip and consumables in the pre-cooled converter;
2. Activate PVDF membrane with methanol for 1 min and rinse with transfer buffer;
3. Install it in the order of "black edge of clip - sponge - filter paper - filter paper - glue -PVDF membrane - filter paper - filter paper - sponge - white edge of clip";
4. The protein was electrotransferred to PVDF membrane. ( 0.45 µm PVDF membrane is recommended ) Reference Table for Selecting PVDF Membrane Pore Size Specifications
Recommended conditions for wet transfer: 200 mA, 120 min.
( Note that the transfer conditions can be adjusted according to the protein size. For high-molecular-weight proteins, a higher current and longer transfer time are recommended. However, ensure that the transfer tank remains at a low temperature to prevent gel melting.)
 
Block
1. After electrotransfer, wash the film with TBST at room temperature for 5 minutes;
2. Incubate the film in the blocking solution for 1 hour at room temperature;
3. Wash the film with TBST for 3 times, 5 minutes each time.
 
Antibody incubation
1. Use primary antibody dilution buffer to prepare the primary antibody working liquid (recommended dilution ratio for primary antibody 1:1000), gently shake and incubate with the film at 4°C overnight;
2. Wash the film with TBST 3 times, 5 minutes each time;
3. Add the secondary antibody to the blocking solution and incubate with the film gently at room temperature for 1 hour;
4. After incubation, wash the film with TBST 3 times for 5 minutes each time.
 
Antibody staining
1. Add the prepared ECL luminescent substrate (or select other color developing substrate according to the second antibody) and mix evenly;
2. Incubate with the film for 1 minute, remove excess substrate (keep the film moist), wrap with plastic film, and expose in the imaging system.

References

  • https://pubmed.ncbi.nlm.nih.gov/18725538/
  • https://pubmed.ncbi.nlm.nih.gov/37422481/

Application Data