Phospho-CDCP1 (Tyr743) Antibody (Rabbit mAb) [N9B6]

製品コード:F8941

印刷

生物学的記述

Specificity Phospho-CDCP1 (Tyr743) Antibody (Rabbit mAb) [N9B6] detects endogenous levels of total CDCP1 protein only when it is Phosphorylated at Tyr743.
Background Phosphorylation of CDCP1 at Tyr743 marks a tyrosine in the cytoplasmic tail of this Src-regulated adhesion receptor. CDCP1, also called Trask (transmembrane and associated with src kinases), is a 140 kDa type I transmembrane glycoprotein that is unrelated to currently known protein families. Src kinases phosphorylate CDCP1 in vitro and drive its hyperphosphorylation in mitosis in vivo. CDCP1 associates with both Yes and Src. During interphase it sits at the cell membrane, and in mitosis it relocalizes to the cytoplasm. Overexpression of CDCP1 causes cell rounding and a loss of adhesion. CDCP1 interacts with adhesion and matrix proteins, including cadherins, syndecans and the membrane-type serine protease 1 (MT-SP1), and MT-SP1 cleaves it. CDCP1 is therefore unusual among cell adhesion molecules because the cell cycle regulates it, and it links Src kinases to the mitotic control of adhesion. Hyperactive Src kinases in tumors may use this link to deregulate adhesion signaling and drive the metastatic phenotype. Phosphotyrosine residues on CDCP1 act as docking sites for signaling proteins. The C2 domain of protein kinase Cδ (PKCδ) binds phosphotyrosine peptides directly and in a sequence-specific manner, and this domain mediates the interaction of PKCδ with CDCP1, a Src-binding glycoprotein. The crystal structure shows a ring-stacking interaction between the phosphotyrosine and a histidine of the C2 domain. PKCδ is the first serine/threonine kinase known to contain a domain that binds phosphotyrosine. The pTyr743 signal therefore reports Src-dependent phosphorylation of CDCP1 and the assembly of a Src-PKCδ signaling complex.

使用情報

Application WB Dilution
WB
1:1000
Reactivity Human
Source Rabbit Monoclonal Antibody MW 93 kDa
Storage Buffer PBS, pH 7.2+50% Glycerol+0.05% BSA+0.01% NaN3
Storage
(from the date of receipt)
-20°C (avoid freeze-thaw cycles), 2 years
WB
Experimental Protocol:
 
Sample preparation
1. Tissue: Lyse the tissue sample by adding an appropriate volume of ice-cold RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail, Phosphatase Inhibitor Cocktail),and homogenize the tissue at a low temperature or lyse it by sonication on ice, then incubate on ice for 30 minutes.
2. Adherent cell: Aspirate the culture medium and wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail, Phosphatase Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
3. Suspension cell: Transfer the culture medium to a pre-cooled centrifuge tube. Centrifuge and aspirate the supernatant. Wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail, Phosphatase Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
4. Place the lysate into a pre-cooled microcentrifuge tube. Centrifuge at 4°C for 15 min. Collect the supernatant;
5. Remove a small volume of lysate to determine the protein concentration;
6. Combine the lysate with protein loading buffer. Boil 20 µL sample under 95-100°C for 5 min. Centrifuge for 5 min after cool down on ice.
 
Electrophoretic separation
1. According to the concentration of extracted protein, load appropriate amount of protein sample and marker onto SDS-PAGE gels for electrophoresis. Recommended separating gel (lower gel) concentration: 5%. Reference Table for Selecting SDS-PAGE Separation Gel Concentrations
2. Power up 80V for 30 minutes. Then the power supply is adjusted (110 V~150 V), the Marker is observed, and the electrophoresis can be stopped when the indicator band of the predyed protein Marker where the protein is located is properly separated. (Note that the current should not be too large when electrophoresis, too large current (more than 150 mA) will cause the temperature to rise, affecting the result of running glue. If high currents cannot be avoided, an ice bath can be used to cool the bath.)
 
Transfer membrane
1. Take out the converter, soak the clip and consumables in the pre-cooled converter;
2. Activate PVDF membrane with methanol for 1 min and rinse with transfer buffer;
3. Install it in the order of "black edge of clip - sponge - filter paper - filter paper - glue -PVDF membrane - filter paper - filter paper - sponge - white edge of clip";
4. The protein was electrotransferred to PVDF membrane. ( 0.45 µm PVDF membrane is recommended ) Reference Table for Selecting PVDF Membrane Pore Size Specifications
Recommended conditions for wet transfer: 200 mA, 120 min.
( Note that the transfer conditions can be adjusted according to the protein size. For high-molecular-weight proteins, a higher current and longer transfer time are recommended. However, ensure that the transfer tank remains at a low temperature to prevent gel melting.)
 
Block
1. After electrotransfer, wash the film with TBST at room temperature for 5 minutes;
2. Incubate the film in the blocking solution ( recommending 5% BSA solution) for 1 hour at room temperature;
3. Wash the film with TBST for 3 times, 5 minutes each time.
 
Antibody incubation
1. Use primary antibody dilution buffer to prepare the primary antibody working liquid (recommended dilution ratio for primary antibody 1:1000), gently shake and incubate with the film at 4°C overnight;
2. Wash the film with TBST 3 times, 5 minutes each time;
3. Add the secondary antibody to the blocking solution and incubate with the film gently at room temperature for 1 hour;
4. After incubation, wash the film with TBST 3 times for 5 minutes each time.
 
Antibody staining
1. Add the prepared ECL luminescent substrate (or select other color developing substrate according to the second antibody) and mix evenly;
2. Incubate with the film for 1 minute, remove excess substrate (keep the film moist), wrap with plastic film, and expose in the imaging system.

References

  • https://pubmed.ncbi.nlm.nih.gov/15851033/
  • https://pubmed.ncbi.nlm.nih.gov/16007225/

Application Data