Phospho-PSD95 (Ser295) Antibody (Rabbit mAb) [J2K16]

製品コード:F8705

印刷

生物学的記述

Specificity Phospho-PSD95 (Ser295) Antibody (Rabbit mAb) [J2K16] detects endogenous levels of PSD95 protein only when phosphorylated at Ser295.
Background PSD-95 is a scaffolding protein of the membrane-associated guanylate kinase (MAGUK) family that organizes the postsynaptic density of excitatory synapses and promotes their maturation and strengthening, a role that depends on its correct localization within that structure. Phosphorylation of serine-295 governs how much PSD-95 is held at the synapse. Phosphorylation at this residue increases synaptic accumulation of PSD-95, its capacity to recruit surface AMPA receptors and its potentiation of excitatory postsynaptic currents, so the modification couples the scaffold to synaptic strength. A Rac1–JNK1 signaling pathway mediates serine-295 phosphorylation and thereby sets the synaptic content of PSD-95. The modification is regulated reciprocally by neuronal activity: chronic elevation of synaptic activity reduces serine-295 phosphorylation while chronic silencing increases it, and NMDA treatment that induces chemical long-term depression causes rapid dephosphorylation. Dephosphorylation is required for synaptic weakening, since overexpressing a phosphomimicking serine-295 mutant prevents NMDA-induced internalization of AMPA receptors and blocks induction of long-term depression. Synaptic strength is therefore regulated bidirectionally by phosphorylation and dephosphorylation of this single residue. A separate site operates in parallel during the same form of plasticity: glycogen synthase kinase-3β phosphorylates PSD-95 on threonine-19, this phosphorylation rises rapidly during chemical long-term depression and falls when the kinase is inhibited pharmacologically or genetically, and it destabilizes PSD-95 within the postsynaptic density. A non-phosphorylatable threonine-19 mutant is more stable in dendritic spines, a phosphomimetic mutant disperses more readily, and overexpressing the non-phosphorylatable form impairs AMPA receptor internalization and long-term depression. Loss of serine-295 phosphorylation and gain of threonine-19 phosphorylation thus both accompany the mobilization of PSD-95 that allows AMPA receptors to be removed from synapses.

使用情報

Application WB Dilution
WB
1:1000
Reactivity Human, Mouse, Rat
Source Rabbit Monoclonal Antibody MW 80 kDa
Storage Buffer PBS, pH 7.2+50% Glycerol+0.05% BSA+0.01% NaN3
Storage
(from the date of receipt)
-20°C (avoid freeze-thaw cycles), 2 years
WB
Experimental Protocol:
 
Sample preparation
1. Tissue: Lyse the tissue sample by adding an appropriate volume of ice-cold RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail, Phosphatase Inhibitor Cocktail),and homogenize the tissue at a low temperature or lyse it by sonication on ice, then incubate on ice for 30 minutes.
2. Adherent cell: Aspirate the culture medium and wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail, Phosphatase Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
3. Suspension cell: Transfer the culture medium to a pre-cooled centrifuge tube. Centrifuge and aspirate the supernatant. Wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail, Phosphatase Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
4. Place the lysate into a pre-cooled microcentrifuge tube. Centrifuge at 4°C for 15 min. Collect the supernatant;
5. Remove a small volume of lysate to determine the protein concentration;
6. Combine the lysate with protein loading buffer. Boil 20 µL sample under 95-100°C for 5 min. Centrifuge for 5 min after cool down on ice.
 
Electrophoretic separation
1. According to the concentration of extracted protein, load appropriate amount of protein sample and marker onto SDS-PAGE gels for electrophoresis. Recommended separating gel (lower gel) concentration: 10%. Reference Table for Selecting SDS-PAGE Separation Gel Concentrations
2. Power up 80V for 30 minutes. Then the power supply is adjusted (110 V~150 V), the Marker is observed, and the electrophoresis can be stopped when the indicator band of the predyed protein Marker where the protein is located is properly separated. (Note that the current should not be too large when electrophoresis, too large current (more than 150 mA) will cause the temperature to rise, affecting the result of running glue. If high currents cannot be avoided, an ice bath can be used to cool the bath.)
 
Transfer membrane
1. Take out the converter, soak the clip and consumables in the pre-cooled converter;
2. Activate PVDF membrane with methanol for 1 min and rinse with transfer buffer;
3. Install it in the order of "black edge of clip - sponge - filter paper - filter paper - glue -PVDF membrane - filter paper - filter paper - sponge - white edge of clip";
4. The protein was electrotransferred to PVDF membrane. ( 0.45 µm PVDF membrane is recommended ) Reference Table for Selecting PVDF Membrane Pore Size Specifications
Recommended conditions for wet transfer: 200 mA, 120 min.
( Note that the transfer conditions can be adjusted according to the protein size. For high-molecular-weight proteins, a higher current and longer transfer time are recommended. However, ensure that the transfer tank remains at a low temperature to prevent gel melting.)
 
Block
1. After electrotransfer, wash the film with TBST at room temperature for 5 minutes;
2. Incubate the film in the blocking solution ( recommending 5% BSA solution) for 1 hour at room temperature;
3. Wash the film with TBST for 3 times, 5 minutes each time.
 
Antibody incubation
1. Use primary antibody dilution buffer to prepare the primary antibody working liquid (recommended dilution ratio for primary antibody 1:1000), gently shake and incubate with the film at 4°C overnight;
2. Wash the film with TBST 3 times, 5 minutes each time;
3. Add the secondary antibody to the blocking solution and incubate with the film gently at room temperature for 1 hour;
4. After incubation, wash the film with TBST 3 times for 5 minutes each time.
 
Antibody staining
1. Add the prepared ECL luminescent substrate (or select other color developing substrate according to the second antibody) and mix evenly;
2. Incubate with the film for 1 minute, remove excess substrate (keep the film moist), wrap with plastic film, and expose in the imaging system.

References

  • https://pubmed.ncbi.nlm.nih.gov/17988632/
  • https://pubmed.ncbi.nlm.nih.gov/23864697/

Application Data