Pontin/RUVBL1 Antibody (Rabbit mAb) [C19J6]

製品コード:F6279

印刷

生物学的記述

Specificity Pontin/RUVBL1 Antibody (Rabbit mAb) [C19J6] detects endogenous levels of total Pontin/RUVBL1 proteins.
Background Pontin (RUVBL1, also called TIP49) is a highly conserved AAA+ ATPase that assembles into multiple large nuclear protein complexes, most notably the TIP60 chromatin-remodeling complex, where it functions alongside its paralog Reptin (RUVBL2) as an essential structural and regulatory component rather than as a standalone enzyme. Within the TIP60 complex, Pontin and Reptin are required for the complex's lysine acetyltransferase activity to proceed at a functional level, even though this requirement does not apply to the isolated, recombinant TIP60 catalytic polypeptide alone, showing that Pontin/Reptin activity is specifically needed to unlock TIP60's enzymatic function within the context of the full assembled complex. Mechanistically, Pontin and Reptin relieve an inhibitory constraint imposed by another TIP60 complex subunit, p400, which otherwise represses TIP60's catalytic activity; Pontin and Reptin competitively displace the SNF2 domain of p400 from its contact with the TIP60 polypeptide, and this displacement, together with a separate, p400-independent role Pontin and Reptin play in maintaining the heat stability of the assembled complex, restores full TIP60 acetyltransferase output, with Pontin and Reptin acting redundantly for both functions and independent of their own ATPase activity. Beyond this structural and de-repressive role in TIP60, Pontin and Reptin also participate in the separate INO80 chromatin-remodeling complex and, while not transcription factors themselves, physically modulate the transcriptional activity of proto-oncogenic transcription factors including MYC and beta-catenin, linking their chromatin-complex assembly function to control of oncogenic gene expression programs. RUVBL1 transcription is itself directly repressed by the transcriptional repressor BCL6, and knocking down BCL6 in a human B-cell lymphoma line significantly upregulates RUVBL1, with an inverse expression relationship between the two proteins observed in certain human lymphomas, indicating that loss of this BCL6-mediated repression is one route by which RUVBL1 becomes elevated in malignancy; RUVBL1/Pontin overexpression has additionally been documented across a wide range of solid and hematologic cancers, consistent with its broader role in supporting oncogenic transcriptional programs through chromatin-remodeling complex assembly.

使用情報

Application WB, ChIP Dilution
WB CHIP
1:1000 1:50
Reactivity Human, Mouse, Rat, Monkey
Source Rabbit Monoclonal Antibody MW 50 kDa
Storage Buffer PBS, pH 7.2+50% Glycerol+0.05% BSA+0.01% NaN3
Storage
(from the date of receipt)
-20°C (avoid freeze-thaw cycles), 2 years
WB
Experimental Protocol:
 
Sample preparation
1. Tissue: Lyse the tissue sample by adding an appropriate volume of ice-cold RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail),and homogenize the tissue at a low temperature or lyse it by sonication on ice, then incubate on ice for 30 minutes.
2. Adherent cell: Aspirate the culture medium and wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
3. Suspension cell: Transfer the culture medium to a pre-cooled centrifuge tube. Centrifuge and aspirate the supernatant. Wash the cells with ice-cold PBS twice. Lyse the cells by adding an appropriate volume of RIPA/NP-40 Lysis Buffer (containing Protease Inhibitor Cocktail) , sonicate to lyse the cells, and incubate on ice for 30 minutes.
4. Place the lysate into a pre-cooled microcentrifuge tube. Centrifuge at 4°C for 15 min. Collect the supernatant;
5. Remove a small volume of lysate to determine the protein concentration;
6. Combine the lysate with protein loading buffer. Boil 20 µL sample under 95-100°C for 5 min. Centrifuge for 5 min after cool down on ice.
 
Electrophoretic separation
1. According to the concentration of extracted protein, load appropriate amount of protein sample and marker onto SDS-PAGE gels for electrophoresis. Recommended separating gel (lower gel) concentration: 10%. Reference Table for Selecting SDS-PAGE Separation Gel Concentrations
2. Power up 80V for 30 minutes. Then the power supply is adjusted (110 V~150 V), the Marker is observed, and the electrophoresis can be stopped when the indicator band of the predyed protein Marker where the protein is located is properly separated. (Note that the current should not be too large when electrophoresis, too large current (more than 150 mA) will cause the temperature to rise, affecting the result of running glue. If high currents cannot be avoided, an ice bath can be used to cool the bath.)
 
Transfer membrane
1. Take out the converter, soak the clip and consumables in the pre-cooled converter;
2. Activate PVDF membrane with methanol for 1 min and rinse with transfer buffer;
3. Install it in the order of "black edge of clip - sponge - filter paper - filter paper - glue -PVDF membrane - filter paper - filter paper - sponge - white edge of clip";
4. The protein was electrotransferred to PVDF membrane. ( 0.45 µm PVDF membrane is recommended ) Reference Table for Selecting PVDF Membrane Pore Size Specifications
Recommended conditions for wet transfer: 200 mA, 120 min.
( Note that the transfer conditions can be adjusted according to the protein size. For high-molecular-weight proteins, a higher current and longer transfer time are recommended. However, ensure that the transfer tank remains at a low temperature to prevent gel melting.)
 
Block
1. After electrotransfer, wash the film with TBST at room temperature for 5 minutes;
2. Incubate the film in the blocking solution for 1 hour at room temperature;
3. Wash the film with TBST for 3 times, 5 minutes each time.
 
Antibody incubation
1. Use primary antibody dilution buffer to prepare the primary antibody working liquid (recommended dilution ratio for primary antibody 1:1000), gently shake and incubate with the film at 4°C overnight;
2. Wash the film with TBST 3 times, 5 minutes each time;
3. Add the secondary antibody to the blocking solution and incubate with the film gently at room temperature for 1 hour;
4. After incubation, wash the film with TBST 3 times for 5 minutes each time.
 
Antibody staining
1. Add the prepared ECL luminescent substrate (or select other color developing substrate according to the second antibody) and mix evenly;
2. Incubate with the film for 1 minute, remove excess substrate (keep the film moist), wrap with plastic film, and expose in the imaging system.

References

  • https://pubmed.ncbi.nlm.nih.gov/23297341/
  • https://pubmed.ncbi.nlm.nih.gov/28884116/

Application Data

WB

Validated by Selleck

  • F6279-wb.gif
    Lane 1: HT1080, Lane 2: NIH/3T3, Lane 3: C6, Lane 4: Cos7